Common problems and solutions of tools in deep hole machining

During deep hole machining, problems such as the dimensional accuracy of the workpiece, surface quality and tool life often occur. How to reduce or avoid these problems is an issue that we urgently need to solve.

1. Problems in deep hole machining: increased hole diameter and large error

(1) Causes

deep hole machining

  • The design value of the reamer outer diameter is too large, or there are burrs on the reamer cutting edge.
  • The cutting speed is too high.
  • The feed rate is inappropriate, or the machining allowance is too large.
  • The main rake angle of the reamer is too large.
  • The reamer is bent.
  • There is a chip tumour on the reamer cutting edge.
  • The swing error of the reamer cutting edge is too large during grinding.
  • The cutting fluid is not suitable.
  • The oil on the surface of the taper shank is not wiped clean when installing the reamer, or the taper surface is scratched.
  • The flat tail of the taper shank is offset, and the taper shank interferes with the cone after being installed in the machine tool spindle.
  • The spindle is bent, or the spindle bearing is too loose or damaged;
  • The reamer is not flexible in floating.
  • The reamer is not coaxial with the workpiece, and the force of both hands is uneven when reaming by hand, causing the reamer to shake left and right

(2) Solutions

  • Reduce the outer diameter of the reamer according to the specific situation.
  • Reduce the cutting speed.
  • Adjust the feed rate or reduce the machining allowance appropriately.
  • Reduce the main deflection angle appropriately.
  • Straighten or scrap the bent and unusable reamer.
  • Use an oilstone to carefully trim it to a qualified level.
  • Control the swing error within the allowable range.
  • Choose a cutting fluid with good cooling performance.
  • Before installing the reamer, the reamer taper shank and the inside of the machine tool spindle taper hole must be wiped clean of oil stains, and the taper surface must be polished with an oilstone.
  • Grind the reamer flat tail.
  • Adjust or replace the spindle bearing.
  • Re-adjust the floating chuck and adjust the coaxiality.
  • Pay attention to correct operation.

2. Problems in deep hole machining: hole diameter reduction

(1) Causes

  • The design value of the reamer’s outer diameter is too small.
  • The cutting speed is too low.
  • The feed rate is too large.
  • The main rake angle of the reamer is too small.
  • The cutting fluid is not selected properly.
  • The worn part of the reamer is not ground off during sharpening, and the elastic recovery reduces the hole diameter.
  • When reaming steel parts, the excess is too large or the reamer is not sharp, which can easily cause elastic recovery, resulting in a reduction in the hole diameter and an unqualified hole diameter.

(2) Solutions

  • Replace the reamer’s outer diameter.
  • Increase the cutting speed appropriately.
  • Reduce the feed rate appropriately.
  • Increase the main rake angle appropriately.
  • Choose an oily cutting fluid with good lubrication performance.
  • Interchange the reamers regularly and sharpen the cutting part of the reamer correctly.
  • When designing the reamer size, the above factors should be considered, or the value should be selected according to the actual situation.
  • Perform trial cutting, take an appropriate excess, and sharpen the reamer.

deep hole machining

3. Problems: The reamed inner hole is not round

(1) Causes

  • The reamer is too long and not rigid enough, causing vibration during reaming.
  • The main rake angle of the reamer is too small.
  • The remaining cutting edge is narrow;
  • The remaining allowance is biased.
  • There are gaps and cross-holes on the surface of the inner hole.
  • There are sand holes and air holes on the surface of the hole.
  • The spindle bearing is loose, there is no guide sleeve, or the clearance between the reamer and the guide sleeve is too large, and the thin-walled workpiece is clamped too tightly, causing the workpiece to deform after removal.

(2) Solutions

  • For reamers with insufficient rigidity, unequal pitch reamers can be used. The installation of the reamer should be rigidly connected to increase the main deflection angle.
  • Select qualified reamers to control the hole position tolerance of the pre-processing process.
  • Use unequal pitch reamers and use longer and more precise guide sleeves;
  • Select qualified blanks.
  • When using equal pitch reamers to ream more precise holes, the machine tool spindle clearance should be adjusted. The matching clearance of the guide sleeve should be required to be higher, or an appropriate clamping method should be used to reduce the clamping force.

4. Problems in deep hole machining: The inner surface of the hole has obvious edges

(1) Causes

  • The remaining allowance is too large.
  • The back angle of the reamer cutting part is too large.
  • The remaining cutting edge is too wide.
  • There are pores and sand holes on the workpiece surface, and the spindle runout is too large.

(2) Solutions

  • Reduce the remaining allowance.
  • Reduce the back angle of the cutting part.
  • Grind the width of the blade band.
  • Select qualified blanks.
  • Adjust the machine tool spindle.

5. Problems in deep hole machining: high surface roughness of the inner hole

(1) Causes

  • Cutting speed is too high.
  • Improper cutting fluid selection;
  • The main rake angle of the reamer is too large, and the reaming cutting edges are not on the same circumference.
  • The remaining allowance is too large.
  • The reaming allowance is uneven or too small, and the local surface is not reamed.
  • The swing difference of the reamer cutting part is out of tolerance, the cutting edge is not sharp, and the surface is rough.
  • The remaining cutting edge band is too wide; the chip removal is not smooth when reaming.
  • The reamer is over-worn.
  • The reamer is damaged, and there are burrs or chipping on the cutting edge.
  • There is a built-up edge on the cutting edge.
  • Due to material reasons, it is not suitable for zero-degree rake angle or negative rake angle reamers.

metal processing, drill bit, solid carbide tools

Carbide Tools Manufacturer >>>

(2) Solutions

  • Reduce cutting speed;
  • Select a cutting fluid according to the material being processed.
  • Appropriately reduce the main deflection angle and correctly sharpen the cutting edge of the reamer;
  • Appropriately reduce the remaining allowance.
  • Improve the position accuracy and quality of the bottom hole before reaming or increase the reaming allowance.
  • Select a qualified reamer.
  • Grind the width of the blade band;
  • Reduce the number of reamer teeth according to the specific situation, increase the chip groove space or use a reamer with a blade inclination angle to facilitate chip removal;
  • Regularly replace the reamer and grind off the grinding area during sharpening.
  • Protective measures should be taken to avoid bruises during sharpening, use and transportation of the reamer;
  • For bruised reamers, use a very fine oilstone to repair the bruised reamer or replace the reamer.
  • Use an oilstone to trim to a qualified level and use a reamer with a front angle of 5°~10°.

6. Problems in deep hole processing: low service life of the reamer

(1) Causes

  • Improper reamer material;
  • The reamer burns during sharpening.
  • Improper cutting fluid selection, cutting fluid fails to flow smoothly, and the surface roughness value of the cutting part and after sharpening is too high.

(2) Solutions

  • Select reamer material according to the processing material; a carbide reamer or a coated reamer can be used.
  • Strictly control the amount of sharpening and cutting to avoid burns.
  • Correctly select the cutting fluid according to the processing material.
  • Clean the chips in the chip groove frequently, use cutting fluid with sufficient pressure, and achieve the requirements through fine grinding or grinding.

7. Problems: The position accuracy of the reamed hole is out of tolerance

(1) Causes

  • The guide sleeve is worn.
  • The bottom end of the guide sleeve is too far from the workpiece.
  • The guide sleeve is short in length, poor in accuracy, and the spindle bearing is loose.

(2) Solutions

  • Regularly replace the guide sleeve.
  • Lengthen the guide sleeve to improve the matching accuracy between the guide sleeve and the reamer.
  • Timely repair the machine tool and adjust the spindle bearing clearance.

8. Problems in deep hole machining: reamer tooth chipping

(1) Causes

  • Too much reaming allowance;
  • Too high hardness of the workpiece material;
  • Too much swing of the cutting edge, uneven cutting load.
  • Too small main rake angle of reamer, increasing the cutting width;
  • Too many chips when reaming deep holes or blind holes, and not cleared in time, or the teeth are worn out during grinding.

(2) Solutions

  • Modify the pre-processed hole size.
  • Reduce the hardness of the material or use a negative rake angle reamer or carbide reamer.
  • Control the swing within the qualified range.
  • Increase the main rake angle; pay attention to clearing chips in time or use a reamer with an edge angle.
  • Pay attention to the grinding quality.

9. Problems in deep hole machining: reamer shank breakage

(1) Causes

  • Too much reaming allowance;
  • Improper allocation of rough and fine reaming allowance and selection of cutting amount when reaming a taper hole;
  • Small chip space of reamer teeth, resulting in chip blockage.

(2) Solutions

  • Modify the pre-processed hole size.
  • Modify the allowance allocation and select the cutting amount reasonably;
  • Reduce the number of reamer teeth, increase the chip space or grind off one tooth of the tooth gap.

10. Problems in deep hole machining: The centre line of the hole is not straight after reaming

(1) Causes

  • The drill hole is deflected before reaming, especially when the hole diameter is small. Due to the poor rigidity of the reamer, the original curvature cannot be corrected.
  • The main rake angle of the reamer is too large.
  • The guide is poor, which makes the reamer easily deviate from the direction during reaming.
  • The back taper of the cutting part is too large.
  • The reamer is displaced in the gap in the middle of the intermittent hole.
  • When reaming by hand, too much force is applied in one direction, forcing the reamer to deflect to one end, destroying the verticality of the reamed hole.

(2) Solutions

  • Add a correction hole for the expansion or boring process.
  • Reduce the main rake angle;
  • Adjust the appropriate reamer.
  • Replace the reamer with a guide part or an extended cutting part.
  • Pay attention to correct operation.
LinkedIn
Reddit
Facebook
WhatsApp
X
Pinterest
Tumblr

Leave a Comment

Your email address will not be published. Required fields are marked *

The Main Supplier Of Cemented Carbide Products In The World

LMM Cemented Carbide specializes in the production of various types of CNC precision cutting tools such as carbide milling cutters, carbide bars, carbide drills, and carbide hobs.

Get In Touch

Contact US

The main supplier of cemented carbide products in the world