Grinding technology of carbide drill bits

Due to the development of high-speed cutting, carbide drill bits have also been widely used. Carbide drill bits are made by welding a carbide blade in the cutting part of the drill bit, as shown in Figure 1. It is suitable for high-speed drilling of hard materials such as cast iron, high manganese steel and hardened steel. The carbide blade material is tungsten carbide K30 (YG8).

The geometric parameters of the cutting part of the carbide drill bit are generally: γo=0°~5°, αo=10°~15°, 2ϕ=110°~120°, ψ=77°, and the main cutting edge is ground into a small arc of R2mm×0.3mm to increase strength.

When using a carbide drill bit, the feed rate should be smaller to avoid blade breakage. The two cutting edges should be ground symmetrically. When encountering an uneven surface of the workpiece or sand holes in the casting, manual feeding should be used to avoid damage to the drill bit.

carbide drill bits, drill bits grinding

Figure 1: Methods for grinding the transverse edge

Grinding of Carbide drill bits

In order to adapt to drilling different materials and meet different drilling requirements, as well as to improve some problems existing in standard twist drills, the grinding work performed when the shape of the cutting part of the drill bit needs to be changed is called grinding. As shown in the figure.

(1) Grinding the chisel edge as shown in Figure 2-a.

The purpose is to shorten the chisel edge and increase the front angle near the drill centre. Generally, drill bits with a diameter of more than 5mm must be ground. The length of the chisel edge after grinding is 1/3 to 1/5 of the original. After grinding, an inner edge is formed, with an inner edge bevel angle ζ = 20° to 30° and a front angle γoζ at the inner edge = 0° to 15°. After grinding, the feed force and scraping phenomenon are reduced, and the centring effect can also be improved.

 

carbide drill bits

a) Grinding the chisel edge   b) Grinding the main cutting edge    c) Grinding the edge    d) Grinding the front cutting edge    e) Grinding the chip groove

Figure 1 shows the relative position of the drill bit and the grinding wheel when grinding the chisel edge.

When grinding, first make the back of the blade contact the grinding wheel, then rotate the drill bit to grind to the front cutting edge and shorten the transverse edge, and at the same time, control the values ​​of the required internal blade rake angle γoζ and internal blade bevel angle ζ. The radius of the grinding wheel corner for grinding the transverse edge should be small, and the grinding wheel diameter should also be smaller; otherwise, it is difficult to grind well, and sometimes the parts that should not be ground on the drill bit may be ground off.

(2) Grinding the main cutting edge (grinding the top angle)

As shown in Figure 2-b, its purpose is to increase the total length and tip angle εr of the cutting edge, improve heat dissipation conditions, increase the strength of the cutter teeth, and enhance the wear resistance of the intersection of the main cutting edge and the edge. This will increase the life of the drill bit and also help reduce the surface roughness of the hole wall.

Generally 2ϕo=70°~75°, fo=0.2D.

carbide drill supplier
Carbide Tools Manufacturer >>>

(3) Grinding the edge

As shown in Figure 2-c, its purpose is to reduce friction on the hole wall and increase the life of the drill bit. Grinding the edge is to grind the secondary back angle α′o=6°~8° on the first secondary back face near the main cutting edge, and keep the edge width at 1/3~1/2 of the original.

(4) Grinding the front face

As shown in Figure 2-d, its purpose is to improve the strength of the cutter teeth when drilling hard materials; when drilling brass, it can also avoid the phenomenon of tool piercing caused by excessively sharp cutting edges. When grinding, grind off a piece of the front face at the intersection of the main cutting edge and the secondary cutting edge (shaded area) to reduce the front angle here.

(5) Grinding the chip groove.

As shown in Figure 2-e, its purpose is to narrow the wide chips and facilitate chip removal. When grinding, grind several staggered chip grooves on the two back faces. Drills with a diameter greater than 15mm can be ground. If some drills have chip grooves on the front face when they are manufactured, there is no need to groove them again. Drills with chip grooves are particularly suitable for drilling steel.

(6) Grinding arc edge.

When grinding various types of group drills, an arc edge is usually ground in the middle of the main cutting edge. When grinding the arc edge, the relative position of the drill bit and the grinding wheel is shown in Figure 3. The cutting edge of the drill bit should be placed in a horizontal position and contact the middle plane of the grinding wheel. The angle between the drill bit axis and the middle plane of the grinding wheel is the back angle αR of the arc edge. During the grinding process, the drill bit cannot swing up and down, but can make a slight rotation as shown in the figure. At the same time, the required arc radius R, inner edge top angle 2ϕ, transverse edge bevel angle ψ, outer edge length l and drill tip height h and other parameters must be controlled.

carbide drill bits

Figure 3: Method of grinding the arc edge

LinkedIn
Reddit
Facebook
WhatsApp
X
Pinterest
Tumblr

Leave a Comment

Your email address will not be published. Required fields are marked *

The Main Supplier Of Cemented Carbide Products In The World

LMM Cemented Carbide specializes in the production of various types of CNC precision cutting tools such as carbide milling cutters, carbide bars, carbide drills, and carbide hobs.

Get In Touch

Contact US

The main supplier of cemented carbide products in the world