(I) Selection of Face Milling Cutter Diameter
The selection of face milling cutter diameter mainly falls into three categories:
(1) When machining a small surface area, choose a cutter or milling cutter with a diameter larger than the width of the surface. This allows for single-pass milling. When the width of the face milling cutter is 1.3 to 1.6 times the width of the surface being machined, it effectively ensures good chip formation and removal.
(2) When machining a large surface area, a milling cutter with a suitable diameter is required, and the surface is milled in multiple passes. The diameter of the milling cutter is limited by machine tool constraints, cutting depth and width, and the size of the insert and tool.

(3) When machining a small surface area with dispersed workpieces, a smaller diameter end mill is required. To maximise machining efficiency, 2/3 of the milling cutter diameter should be in contact with the workpiece, i.e., the milling cutter diameter should be 1.5 times the width being milled. During climb milling, using this ratio of cutter diameter to cutting width appropriately will ensure that the milling cutter has a very suitable angle when entering the workpiece. If it’s uncertain whether the machine tool has sufficient power to maintain the milling cutter’s cutting width at this ratio, the axial cutting thickness can be completed in two or more stages to maintain the milling cutter diameter to cutting width ratio as much as possible.
(II) Selection of Milling Cutter Tooth Count
When selecting a milling cutter for machining, the number of teeth must be considered. For example, a 100mm diameter sparse-tooth milling cutter has only 6 teeth, while a 100mm diameter close-tooth milling cutter can have 8 teeth. The density of the teeth affects production efficiency and product quality. Closer teeth increase production efficiency and improve workpiece quality, but also hinder chip removal. Based on tooth diameter, milling cutters can be categorised as sparse, close, and dense.
Sparse-tooth milling cutters are used for rough machining, using 1-1.5 inserts per 25.4mm diameter. They offer a larger chip clearance and are suitable for cutting soft materials that produce continuous chips. Long inserts and wide-width cutting are used. Dense-tooth cutting is advantageous for machining under stable conditions and is generally used for roughing cast iron. It is also suitable for shallow cutting, narrow cutting, and cutting where chip space is not required in high-temperature alloys.
Dense-tooth cutting is used in finish milling, with an axial depth of cut of 0.25–0.64 mm. The cutting load per tooth is small, requiring less power, making it suitable for machining thin-walled materials. The tooth pitch determines the number of teeth simultaneously involved in cutting during milling. At least one insert should be cutting during the cutting process to avoid milling impacts that could damage the tool and overload the machine tool.
Furthermore, the selection of the insert tooth count must ensure that the chips are properly curled and easily removed from the cutting zone. Inadequate chip space will lead to chip entrapment, damaging the cutting edge and potentially the workpiece. Simultaneously, the inserts should have sufficient density to ensure that at least one insert is cutting at any given time during the cutting process. Failure to do so will cause severe impacts, leading to cutting-edge breakage, tool damage, and machine tool overload.

(III) Selection of Tool Angles
Tool cutting angles can be positioned relative to the radial and axial planes as positive, negative, and zero rake angles. Since a zero rake angle would cause the entire cutting edge to impact the workpiece simultaneously, it is generally not used. The selection of face milling cutter angles affects the face milling contact method. To minimise tool impact, reduce tool breakage, and avoid STUV (Straight-Tube Unreacted) face milling contact, the face milling cutter’s geometry must be considered along with the tool entry angle. The combination of radial and axial rake angles determines the cutting angle. Commonly used basic combinations include: negative radial and negative axial rake angles; positive radial and positive axial rake angles; negative radial and positive axial rake angles; and positive radial and negative axial rake angles.
Tools with both negative radial and axial rake angles (hereinafter referred to as “double negative”) are mostly used for roughing cast iron and cast steel, but require high machine tool power and sufficient rigidity. “Double negative” inserts have high cutting-edge strength and can withstand large cutting loads. Tools with both negative angles also require high rigidity of the machine tool, workpiece, and fixture.
Tools with both positive axial and radial rake angles (hereinafter referred to as “double positive”) increase the cutting angle, resulting in smooth cutting and efficient chip removal, but the cutting edge strength is relatively poor. This combination is suitable for machining soft materials and stainless steel, heat-resistant steel, ordinary steel, and cast iron. This combination should be preferred for low-power machine tools, systems with insufficient rigidity, and when a built-up edge is present.
A combination of a negative radial rake angle and a positive axial rake angle increases the strength of the cutting edge due to the negative radial rake angle, while the positive axial rake angle generates a shearing force. This combination provides strong impact resistance and a sharper cutting edge, making it suitable for large-mast milling of steel, cast steel, and cast iron.
A positive radial rake angle and a negative axial rake angle cause chip breaking to occur below the centre, which can scratch the machined surface, resulting in poor chip removal.
(IV) Selection of Milling Inserts
The selection of milling inserts is also a consideration in face milling. Pressed inserts are more suitable for certain machining applications; sometimes, ground inserts are also necessary.
For roughing, pressed inserts are preferred as they reduce machining costs. While pressed inserts have lower dimensional accuracy and edge sharpness than ground inserts, they offer better edge strength, making them more impact-resistant and capable of handling larger depths of cut and feed rates for rough milling. Pressed inserts have chip grooves on the rake face, reducing cutting forces and friction with the workpiece and chips, thus lowering power requirements. However, pressed inserts have a less dense surface than ground inserts, resulting in lower dimensional accuracy and greater variation in tip height across the cutter body. Due to their lower cost, pressed inserts are widely used in production.
For finish milling, ground inserts are preferred. These inserts offer better dimensional accuracy, leading to higher positioning accuracy of the cutting edge during milling, resulting in higher machining precision and lower surface roughness. Furthermore, the trend in the development of ground milling inserts for finish milling is towards incorporating chip grooves to create a large positive rake angle cutting edge, allowing for smaller feed rates and depths of cut. Carbide inserts without a sharp rake angle will have their tips rub against the workpiece when machining with small feed and shallow depth of cut, reducing tool life.